there was a post about remving choke and light switch and starter and just wiring up kill switch and now i cant find it please help me

i will look and see what i can find for you. pm me your email address and i can send it to you through a word file

Removing Black blob

The orange/white and solid orange wire are the tricky part. There are two orange/white wires, so the best thing to to is get everything else wired up, strip all the orange and orange/white wires and try one orange/whit and orange combo at a time until it starts. Thats what I did.

I don't know if all three can be wired together or not, didn't try it.

just wire the high and the low beems together, it is really easy...

Wire all the light wires together? Won't that cause a short?

thank you for the help it should just have both high and low beams turn on at same time with the key

ya, no it wont cause a short, thats what i have done and many of others, read in the black blob thread he did it on his LTR too, when your turn your key to your lights on it just has both on at same time, saves you wiring up a switch for high/low beams, and finding where to locate switch, much easier believe me i did this both ways and am much happier with them wired together. There are 3 wires for lights, high low, and i think ground? idk you just wire all three together and you are good togo

k thanx for help now can i use the pro amror kill switch instead of pingel because pingel is almost 100 bucks?


or what kill switch should i run, and also what puch button should i run?

I run the pro armor, and i have no problems, a lotta people say it is the wrong one to use because it can fry the CDI box because you hook it to the coil instead of the on/of wires. If you dont pull it then you should be fine, if you do have to then that may happen, i have pulled mine to be sure that it works and my CDI is fine, i do know that it does void the warrenty on the dyna techs though, i dunno if it is normally open or normally closed you want, hopefully some one else can pitch in...

Ok thx for that info. I hate the low beams because they only aim at the groun soimma re-wire mine so he lows are aiming down and highs forward all at the same time.

Thx again pal.

no prob, you goin to get ridda the black blob too, makes it look a lot better, and it is soooooooo easy to do, and only like 10 bucks... if you dont get a tether kill

So how clean my bars look?

o nvm, shoulda read your sig, you already have o well haha thats for Z400man then...

Yea Just I'm gonna re-wire the lights.

Hey Mitch, where did you mount your key switch?

i think i got him fixed up... i think mitch mounted his key switch on the frame right below the gas tank on the right side. i could be wrong though

i justc alled pro armor and they said there kill switches are normally closed just like the pingel ones does any one run that and how does it do?


and i got one more ? bout it when u wana shut bike off do you pull the kill switch or just turn the key off?

Ya thats where mine is, it seems like a pretty good spot doesnt get too dirty, and once you know where it is it is easy to find, other people are like wtf how the hell do i start this!?!?!



Thats what i run and havent had any problems, i dont think they are like the pingles, maybe the cheaper versions... apparently i run the wrong kind the should be normally open i guess?!!?!? little help, idk a lotta bout this

yea normally closed is what u want just like u got. how do you shut your bike off witht he key or pull the kill switch

key

k thats what i thought i will post pics up when its completed to see how it came out thank you all for the help

no problem... wont be too hard to do, shouldnt take more than about 15 minutes, even if you use the soldering gun, like me, i also stall it too, just depends on how i feel...

you should be able to just pull the kill switch if you want. it just opens the connection, cant see why not?